Lathe, metal (Challenger 1660G) ID:46: Difference between revisions

From Protospace Wiki
Jump to navigation Jump to search
(Additional filling out of tooling table.)
(→‎Documents: add subcategory placeholders ToDo)
 
(30 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{Equipment page
{{Equipment page
| toolname = Metal lathe
| toolname = Metal lathe
| model = Challenger 1660G (a.k.a. Birmingham LUX 1660G and YCL-1660)
| model = Challenger 1660G (aka Birmingham LUX 1660G or YCL-1660)
| serial = ??
| serial = ??
| owner = Protospace
| owner = Protospace
Line 7: Line 7:
| arrived = 2015-12-22
| arrived = 2015-12-22
| location = Metal shop
| location = Metal shop
| status = Needs Work: needs to be cleaned and set up
| status = Working
| permission = Open to full members
| permission = Open to full members
| certification = Certification Required: [[lathe training]] or (upcoming as of 2015-12) lathe/mill training
| certification = [https://my.protospace.ca/courses/281 Metal Cutting & Manual Lathe]
| id = 46
| id = 46
| itemphoto = [[File:46.jpg|350px|thumb|right|]]
| itemphoto = [[File:46.jpg|350px|thumb|right|]]
Line 53: Line 53:
*Safety foot brake
*Safety foot brake


<br />
==Jank==
===Carriage Lock===
If the carriage doesn't freely/easily move in the X direction, there's a fat hex bolt head sticking up on the right side of it that needs loosening.
(add pic here)
===Power Feed===
Note that while <u>generally gears/speeds shouldn't be changed while the lathe is in motion</u>, from https://forum.protospace.ca/t/can-t-get-lathe-power-feed-to-work/3568/8<blockquote>Set it to a lowish speed like 400 or less and bump the jog button. Then start wiggling leavers while it’s coasting down and watch the drive shaft and screw. You’ll feel it when it engages and the shafts will start spinning…
The threading lead screw and the power feed drive shaft are taken off at different points in the gear train. It is possible to jiggle a leaver and get one to start spinning while the other is still not engaged properly and requires further jiggling.
The XYWZ lever is the worst and usually requires persuasion to engage. The gears are all straight cut, and all may require sufficient wigglage before they cooperate. And the number dial is keep turning until it works. It’s about 1/4 past the number you want.</blockquote>[[File:20180206_230213_720p.mp4|frameless]]
<br />
==Documents==
=== Reference ===
*[http://www.southern-tool.com/store/birmingham_lux-1640-g_lathes.php Sales page for 1640T and 1660T models]
*According to those in the know (Danny P and John W) there are three manuals for this machine:
*[https://wiki.protospace.ca/images/c/c2/Lux_Matter_Metal_Lathe_Manual_1660G.pdf 1640G/1660G Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/2/2c/Lux-Matter_1660T_Manual_from_Luc_Archer.pdf 1640T/1660T Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/5/5e/LUX-Matter_1600_Series_Instruction_Manual.pdf 1500/1600 Instruction Manual and Parts List]
=== Training ===
(training material linked here?)
=== Practical Project ===
(tired of digging this out of drive, insert here?)<br />
==Tooling==
==Tooling==
{| class="wikitable mw-collapsible mw-collapsed"
{| class="wikitable mw-collapsible mw-collapsed"
|+
|+
!Short Description
!Short Description
!Shank Size
!Shank Size
Line 67: Line 100:
!Manufacturer
!Manufacturer
!New Price
!New Price
!Condition
!Notes
!Notes
|-
|-
Line 73: Line 107:
|GIE-7
|GIE-7
|Right Hand, 4.5" long, grooving, parting and turning tool
|Right Hand, 4.5" long, grooving, parting and turning tool
|
|[[File:THE-7-3 8-R.jpg|150px]]
|THE-7-3/8-R
|THE-7-3/8-R
|
|
Line 79: Line 113:
|
|
|Nicole
|Nicole
|110.7
|$110.7
|Good
|
|
|-
|-
Line 85: Line 120:
|3/4 "
|3/4 "
|CCMT33x, CCxT33x
|CCMT33x, CCxT33x
|Boring bar, RH, 8" long
|Boring bar, RH, 7" (174 mm) long
|[[File:BoringBar174 small.jpg|150px]]
|
|
|
|
|
|
|
|
|
|
|Poor
|Damage reduces insert support.  Missing insert screw.
|-
|Boring Bar
|3/4 "
|CCMT33x, CCxT33x
|Boring bar, RH, 5 3/4" (144 mm) long
|[[File:BoringBar144 small.jpg|150px]]
|
|
|
|
|
|
|
|
|
|
|Poor
|Damage reduces insert support. Missing insert screw.
|-
|-
|Boring Bar
|Boring Bar
|3/4 "
|3/4 "
|CCMT33x, CCxT33x
|CCMT33x, CCxT33x
|Boring bar, RH, 6" long
|Boring bar, RH, 4 7/8" (121 mm) long
|
|[[File:BoringBar121.jpg|150px]]
|
|
|
|
|
Line 107: Line 156:
|
|
|
|
|Serviceable
|Missing insert screw.
|-
|-
|Boring Bar
|Boring Bar
Line 112: Line 163:
|CCMT33x, CCxT33x
|CCMT33x, CCxT33x
|Boring bar, RH, 8" long
|Boring bar, RH, 8" long
|[[File:SER 1000 M16.jpg|150px]]
|
|
|
|
Line 118: Line 170:
|
|
|
|
|
|Fair
|
|Missing insert screw.
|-
|-
|Threading Insert Holder
|Threading Insert Holder
|1"
|1"
|
|Full form or partial form.  See notes.
|Threading insert holder
|Threading insert holder
|
|[[File:IscarThreadingInsertHolder.jpg|150px]]
|SER 1000 M16
|SER 1000 M16
|
|
Line 132: Line 184:
|Iscar
|Iscar
|US$158.62
|US$158.62
|
|Fair
|Scuffing.  See manufactures documentation for insert selection.
Image shows regular turning insert, not threading insert.
|-
|-
|Triangular R Insert Holder
|Triangular RH, G Insert Holder
|3/4"
|3/4"
|
|TNMG43x, TNxG43x
|
|Triangular RH, ANSI G Type
|
|[[File:MTJNRS 46- 4 D.jpg|150px]]
|
|
|MTJNRS 46- 4 D
|MTJNRS 46- 4 D
Line 145: Line 199:
|Valenite
|Valenite
|
|
|ANSI shank numbers are flipped.
|Serviceable
|ANSI shank numbers are flipped.  Damaged shank.  Shank has been machined.
|-
|-
|Triangular RH Insert Holder
|Triangular RH, J Insert Holder
|3/8"
|3/8"
|
|TNMG32x, TNxG32x
|
|Triangular RH, ANSI J Type
|
|[[File:TBR12_3_8_IC.jpg|150px]]
|
|
|TBR12 3/8 I.C.
|TBR12 3/8 I.C.
Line 158: Line 213:
|Carboloy
|Carboloy
|
|
|Fair
|
|
|-
|-
|Parting Tool Holder
|3/4"
|HSS
|HSS parting tool holder.  Quick change for 3/4" tool post.
|[[File:PartingToolHolder_small.jpg|150px]]
|
|
|
|
Line 166: Line 227:
|
|
|
|
|
|Good
|
|
|
|
|
|
|}
|}
==Documents==
*[http://www.southern-tool.com/store/birmingham_lux-1640-g_lathes.php Sales page for 1640T and 1660T models]
*According to those in the know (Danny P and John W) there are three manuals for this machine:
*[https://wiki.protospace.ca/images/c/c2/Lux_Matter_Metal_Lathe_Manual_1660G.pdf 1640G/1660G Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/2/2c/Lux-Matter_1660T_Manual_from_Luc_Archer.pdf 1640T/1660T Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/5/5e/LUX-Matter_1600_Series_Instruction_Manual.pdf 1500/1600 Instruction Manual and Parts List]


==History==
==History==

Latest revision as of 21:28, 24 February 2023

← Back to tools we have

46.jpg
Type Metal lathe
Make/Model Challenger 1660G (aka Birmingham LUX 1660G or YCL-1660)
Serial number ??
Original owner Protospace
Loan status Owned by Protospace
Arrival date 2015-12-22
Location Metal shop
Functional status Working
Usage permissions Open to full members
Certification Metal Cutting & Manual Lathe
Wiki-ID 46
Label 1.0" 1.5" 2.0"

Specifications

All from the 1640T/1660T page listed in the Documents section unless noted.

  • Dimensions: 29" deep × 72" long × ?? tall (according to John W)
  • Mass: ~4000–5000 lbs
  • Motor: 7.5 hp, 3-phase, 220 V
  • 36–1800 RPM spindle speed in 12 steps
  • Capacities
    • Swing over bed: 16"
    • Swing over cross slide: 10"
    • Distance between centers: 60"
    • Swing in gap: 60"
    • Width of bed: 24"
  • Headstock
    • Spindle nose: ASA D1-6
    • Spindle bore: 2 1/16" or 2 1/8"
    • Spindle taper: MT 6
    • Spindle speeds: 36, 60, 82, 93, 158, 215, 302, 510, 695, 786, 1328, 1800 rpm
  • Threads & feeds
    • Imperial threading: 2–72 TPI (45 kinds)
    • Metric threading: 0.2–14mm (40 kinds)
    • Module pitch threading: 0.3–3.5 M.P. (18 kinds) (for making shafts for worm gears)
    • DP threading: 8–44 DP (21 kinds)
    • Longitudinal feed range: 0.002"–0.04" ipr
    • Cross feed range: 0.001"–0.02" ipr
  • Carriage
    • Cross slide travel: 8 1/4"
    • Compound slide travel: 5 1/4"
  • Tailstock
    • Center taper: MT 4
    • Quill travel: 6 1/4"
    • Quill diameter: 2 1/16"
  • Coolant pump
  • Safety foot brake


Jank

Carriage Lock

If the carriage doesn't freely/easily move in the X direction, there's a fat hex bolt head sticking up on the right side of it that needs loosening.

(add pic here)

Power Feed

Note that while generally gears/speeds shouldn't be changed while the lathe is in motion, from https://forum.protospace.ca/t/can-t-get-lathe-power-feed-to-work/3568/8

Set it to a lowish speed like 400 or less and bump the jog button. Then start wiggling leavers while it’s coasting down and watch the drive shaft and screw. You’ll feel it when it engages and the shafts will start spinning…

The threading lead screw and the power feed drive shaft are taken off at different points in the gear train. It is possible to jiggle a leaver and get one to start spinning while the other is still not engaged properly and requires further jiggling.

The XYWZ lever is the worst and usually requires persuasion to engage. The gears are all straight cut, and all may require sufficient wigglage before they cooperate. And the number dial is keep turning until it works. It’s about 1/4 past the number you want.


Documents

Reference

Training

(training material linked here?)

Practical Project

(tired of digging this out of drive, insert here?)

Tooling

Short Description Shank Size Typical Insert Types Long Description Photo Manuf Code ANSI ISO Replacement Screw Type Manufacturer New Price Condition Notes
Grooving Insert Holder 3/8 " GIE-7 Right Hand, 4.5" long, grooving, parting and turning tool THE-7-3 8-R.jpg THE-7-3/8-R Nicole $110.7 Good
Boring Bar 3/4 " CCMT33x, CCxT33x Boring bar, RH, 7" (174 mm) long BoringBar174 small.jpg Poor Damage reduces insert support. Missing insert screw.
Boring Bar 3/4 " CCMT33x, CCxT33x Boring bar, RH, 5 3/4" (144 mm) long BoringBar144 small.jpg Poor Damage reduces insert support. Missing insert screw.
Boring Bar 3/4 " CCMT33x, CCxT33x Boring bar, RH, 4 7/8" (121 mm) long BoringBar121.jpg Serviceable Missing insert screw.
Boring Bar 1" CCMT33x, CCxT33x Boring bar, RH, 8" long SER 1000 M16.jpg Fair Missing insert screw.
Threading Insert Holder 1" Full form or partial form. See notes. Threading insert holder IscarThreadingInsertHolder.jpg SER 1000 M16 Iscar US$158.62 Fair Scuffing. See manufactures documentation for insert selection.

Image shows regular turning insert, not threading insert.

Triangular RH, G Insert Holder 3/4" TNMG43x, TNxG43x Triangular RH, ANSI G Type MTJNRS 46- 4 D.jpg MTJNRS 46- 4 D Valenite Serviceable ANSI shank numbers are flipped. Damaged shank. Shank has been machined.
Triangular RH, J Insert Holder 3/8" TNMG32x, TNxG32x Triangular RH, ANSI J Type TBR12 3 8 IC.jpg TBR12 3/8 I.C. Carboloy Fair
Parting Tool Holder 3/4" HSS HSS parting tool holder. Quick change for 3/4" tool post. PartingToolHolder small.jpg Good

History

This lathe was bought by Protospace using funding approved for the purchase of new machine tools at the December 2015 members' meeting. It was picked up and brought to Protospace on 2015-12-22 along with the ACRA mill and the new 80-gallon air compressor. It replaces Kyle Paavola's lathe; it has equivalent capability. It came with the following accessories:

  • 3-jaw chuck
  • 4-jaw chuck
  • Big steady rest
  • Taper attachment
  • 40-position tool post and one tool holder with a carbide tool holder in it
  • Live center
  • A carriage stop with a micrometer
  • Coolant pump
Retrieved from "https://wiki.protospace.ca/index.php?title=Lathe,_metal_(Challenger_1660G)_ID:46&oldid=6397"