Embroidery machine, CNC (Tajima TEJT II-C NEO 1501) ID:144: Difference between revisions

Jump to navigation Jump to search

Embroidery machine, CNC (Tajima TEJT II-C NEO 1501) ID:144 (view source)

Revision as of 01:05, 26 December 2022

833 bytes added ,  26 December 2022
→‎Troubleshooting
Line 41: Line 41:
L-type bobbin, takes 80wt thread, threads clockwise out under spring and through metal eyelet, leave 2" tail. Observe lubing requirements before reinserting.
L-type bobbin, takes 80wt thread, threads clockwise out under spring and through metal eyelet, leave 2" tail. Observe lubing requirements before reinserting.


===Troubleshooting===
<br />
 
====Machine Detected a Thread Breakage====
[https://forum.protospace.ca/t/troubleshooting-the-embroidery-machine-tip/2418 See this forum post]
 
====2BA - Memory Capacity Exceeded Error====
Clear previous jobs stored in the memory:
 
*Each time a job is loaded from the USB stick the job is transferred to the internal memory of the Tajima.
*In Memory Mode - Multi, the job is added to the list of jobs.
*In Memory Mode - Single, the new job overwrites the last job held in internal memory.
*When the internal Tajima memory is full a 2BA error will occur after pressing Data and choosing the job file from the USB.
*The 2BA error may occur instantly or near the end of the file load process depending on when the limit is reached.
*If the internal memory is very full, pressing the Data button to pick a USB file will give no response as if the Data button is broken.
*When the Tajima is too full to show the 2BA error, data can be deleted just as if the 2BA error had appeared.
*
*Press down to select
*3. Delete Data to remove a single job or to
*5. Initial Memory - to remove all jobs from memory and initialize internal storage[[File:TajimaDataM1.png|none|thumb|Data Menu]][[File:TajimaDataM3.png|thumb|Data Menu 3|alt=|none]]<br />
*There is no way to save a list of internal jobs out.
*Keep a copy of your Jobs on a USB stick.
*It is convenient if you are doing multiple jobs in a single session to keep them in internal memory.
*Just remember jobs saved to the Internal Tajima memory may be cleared by the next member using the machine.
*As a curtesy to the next user who may be a beginner and not know about 2BA error, clear the memory at the end of your session.


===Quick Start===
== Quick Start ==
{{Warning|This "cheat sheet" is not a substitute for proper training and confidence in operating this very nice and expensive machine! If you're feeling unsure, ask for help!}}
{{Warning|This "cheat sheet" is not a substitute for proper training and confidence in operating this very nice and expensive machine! If you're feeling unsure, ask for help!}}


Line 109: Line 86:


<br />
<br />
==Troubleshooting==
====Machine Detected a Thread Breakage====
[https://forum.protospace.ca/t/troubleshooting-the-embroidery-machine-tip/2418 See this forum post]
====2BA - Memory Capacity Exceeded Error====
Clear previous jobs stored in the memory:
*Each time a job is loaded from the USB stick the job is transferred to the internal memory of the Tajima.
*In Memory Mode - Multi, the job is added to the list of jobs.
*In Memory Mode - Single, the new job overwrites the last job held in internal memory.
*When the internal Tajima memory is full a 2BA error will occur after pressing Data and choosing the job file from the USB.
*The 2BA error may occur instantly or near the end of the file load process depending on when the limit is reached.
*If the internal memory is very full, pressing the Data button to pick a USB file will give no response as if the Data button is broken.
*When the Tajima is too full to show the 2BA error, data can be deleted just as if the 2BA error had appeared.
*
*Press down to select
*3. Delete Data to remove a single job or to
*5. Initial Memory - to remove all jobs from memory and initialize internal storage[[File:TajimaDataM1.png|none|thumb|Data Menu]][[File:TajimaDataM3.png|thumb|Data Menu 3|alt=|none]]<br />
*There is no way to save a list of internal jobs out.
*Keep a copy of your Jobs on a USB stick.
*It is convenient if you are doing multiple jobs in a single session to keep them in internal memory.
*Just remember jobs saved to the Internal Tajima memory may be cleared by the next member using the machine.
*As a curtesy to the next user who may be a beginner and not know about 2BA error, clear the memory at the end of your session
=== Stop Position Error (211) ===
[[File:Stop error control.jpg|left|thumb]]
<br />
A stop position error on the Tajima means that the Tajima stopped unexpectedly potentially due to a collision with the frame.  To resolve the error perform the following steps:
[[File:Stop Position Error.png|left|thumb]]
# Dismiss the error using the red "O"/Stop key on the keypad.
# (Refer to the manual excerpt on the left for the following steps)
# Rotate the main shaft until the circled indicator disappears in the status display
# Perform a manual color change, by selecting a different color using the manual color change keys on the bottom right of the keypad.  Once a different color is selected press the "set" key to confirm the manual color change.
# Once the manual color change is complete you may resume your stiching.
Retrieved from "https://wiki.protospace.ca/Special:MobileDiff/6255"

Navigation menu