Table saw (SawStop) ID:172: Difference between revisions
No edit summary |
(Add troubleshooting instructions for tilt control) |
||
| Line 45: | Line 45: | ||
If the riving knife is truly misaligned, follow [https://thenewbiewoodworker.com/2019/06/12/adjusting-and-aligning-the-riving-knife.html this procedure]. | If the riving knife is truly misaligned, follow [https://thenewbiewoodworker.com/2019/06/12/adjusting-and-aligning-the-riving-knife.html this procedure]. | ||
'''How to remove the side access panel''' | |||
Since the side access panel doesn't open all the way, you can just remove it by pulling out the metal pin downward. | |||
'''Tilt control is lost / loose''' | |||
The tilt control wheel can become loose or disconnected if an internal collar falls off. | |||
* Open / remove the side access panel (see above) | |||
* Find both the [[Media:Sawstop-bushing-collar.jpg|bushing and collar]] | |||
* Grab a 3 mm hex driver (yellow T-handled ones can be found near metal lathe) | |||
* Re-engage control wheel and turn all the way to 45'''°''' | |||
* Reinstall bushing and collar on shaft [[Media:Sawstop-bushing-collar-installed.jpg|like this photo]], tighten set screw | |||
==Documentation== | ==Documentation== | ||
Revision as of 01:13, 11 December 2023
 | |
| Type | Table saw |
| Make/Model | PCS31230 |
| Serial number | ? |
| Original owner | Protospace |
| Loan status | ? |
| Arrival date | ? |
| Location | Wood shop |
| Functional status | Working |
| Usage permissions | Open to full members |
| Certification | SawStop specific training required |
| Wiki-ID | 172 |
| Label | 1.0" 1.5" 2.0" |
Specs
10" SawStop table saw. Purchased used in 2023.
Has technology that if you accidentally touch a moving saw blade, the blade is clamped down within about 3 ms, reducing or hopefully avoiding serious personal injury.
Usage
Size of blade is critical.
Sawstop recommends a blade size of 10", plus or minus 1/16". A blade may be smaller than this this due to repeated sharpenings, and the clamping cartridge cannot be adjusted properly, and that will either take longer to clamp down in case of "triggering", not allow the saw to start, or if the blade is oversize, may cause immediate triggering, failure to start or maybe other problems.
Accidentally triggering the safety feature will result in a cost of around $135 to replace the cartridge, and $80-120 to replace the blade, costs which will be the responsibility of the member.
Requirements for using this are evolving, and as this is not your typical table saw, so you have to do your due diligence and read and understand how it operates.
Wet lumber, metal particles, including staples can trigger it. So members will have to take an upgrade certification to be able to use your card to operate it!
Troubleshooting
Saw won't turn on
- Ensure it's plugged into the wall (cord is labelled)
- Ensure you've authorized with the lockout and the green LED is on
- Wait until the red LED on the SawStop has stopped blinking, then pull the paddle
Riving knife is misaligned
Make sure sawdust isn't jammed in: loosen the lever and blow out beside the riving knife with shop air.
Make sure the riving knife hasn't been bent: confirm misalignment near the base with a ruler.
If the riving knife is truly misaligned, follow this procedure.
How to remove the side access panel
Since the side access panel doesn't open all the way, you can just remove it by pulling out the metal pin downward.
Tilt control is lost / loose
The tilt control wheel can become loose or disconnected if an internal collar falls off.
- Open / remove the side access panel (see above)
- Find both the bushing and collar
- Grab a 3 mm hex driver (yellow T-handled ones can be found near metal lathe)
- Re-engage control wheel and turn all the way to 45°
- Reinstall bushing and collar on shaft like this photo, tighten set screw
Documentation
TBD
History
2023-12-10: Triggered on metallic angle cutting jig. No flesh was involved.