80 watt laser engraver: Difference between revisions

Jump to navigation Jump to search
no edit summary
No edit summary
No edit summary
Line 26: Line 26:


== Using the machine ==
== Using the machine ==
regurgitate the above here
3 Procedures must be followed as prescribed
# Safe Power Up Procedure to be performed whenever the machine needs to be turned on
# Pre-Cut Check to be performed before the first cut and after any break between cuts, don't assume the machine is as you left it.
# Safe Power Down Procedure


=== Powering up the machine ===
=== Safe Power Up Procedure ===
With very few exceptions, the same order of operations should always be maintained for safe proper operation.  Failing to enable a portion of the cooling system will damage the laser.
With very few exceptions, the same order of operations should always be maintained for safe proper operation.  Failing to enable a portion of the cooling system will damage the laser.
# Open cutting area and remove any objects from the working bed.
# Verify the cooling tank has enough water.  
# Verify the cooling tank has enough water.  
# Plug in circulation pump to a 110v circuit. (currently does not power on with chiller),
# Turn on the circulation pump, sometimes it's unplugged from the black power bar, sometimes the black power bar is turned off, plug it into the black power bar ONLY, and ensure the power bar is on.
# Power on 120-240 voltage converter (box on trolley with green light-up switch).
# Power on 120-240 voltage converter (box on trolley with green light-up switch).
#* Verify that power is applied to the chiller and air pump.  These are 220v appliances and need to be plugged directly into the voltage converter.
#* Verify that power is applied to the chiller and air pump.  These are 220v appliances and need to be plugged directly into the voltage converter. The display panel on the chiller should light up, and the hanging pump should now be vibrating.  
# Set up ventilation fan outdoors, leave unplugged but switch unit on. 
#* During colder temperatures only run exhaust while cutting is taking place.
# Activate power to laser cutter from switch on back of unit.
# Activate power to laser cutter from switch on back of unit.
# Deactivate E-stop with a twisting motion, and power on laser with key switch on front panel. The key had 3 positions, rotating clockwise the positions are off, off, on.  
# Deactivate E-stop with a twisting motion, and power on laser with key switch on front panel. The key had 3 positions, rotating clockwise the positions are off, off, on.  


The laser is now active and ready to accept instructions from the laptop.
The laser is now active and ready to accept instructions from the computer.
'''Warning!'''  The laser is a stand-alone unit and ''can move/execute programs/fire the laser with the laptop disconnected.''
'''Warning!'''  The laser is a stand-alone unit and ''can move/execute programs/fire the laser with the laptop disconnected.''
=== Pre-Cut Check ===
# Ensure the circulation pump is running
# Ensure the air pump is running
# Ensure the exhaust fan is on (this one will frequently be turned off between cuts so always check it)
# Verify the work area is free of obstructions
# With a hand over the E-Stop, run a test to see if the cut envelope will cause the head to collide with any obstructions (weights, sides) Do not allow the head to collide with ANYTHING when in doubt hit the E-STOP and reset with the workpeice re-positioned or the obstructions removed, in extreme cases you may have to modify or abandon the cut.
=== Shutting down the machine ===
Following the same steps in reverse order will help ensure the machine is left in a safe mode.
# Activate E-stop to render the work-area safe. 
# Clean out remnants from the cutting area.
# Turn off power from the key switch, this will turn off the work-light.
# Turn off the power switch at the back of the laser.
# Deactivate the exhaust fan
# Power down voltage converter (green switch)
# Unplug circulation pump


=== Focusing the Laser ===
=== Focusing the Laser ===
Line 76: Line 94:
#* To abort the current program (something is horribly wrong), press the stop key.  This will abort the program and it will have to be restarted from the start.  The head should home back to the origin from before the program was started.
#* To abort the current program (something is horribly wrong), press the stop key.  This will abort the program and it will have to be restarted from the start.  The head should home back to the origin from before the program was started.


=== Shutting down the machine ===
Following the same steps in reverse order will help ensure the machine is left in a safe mode.
# Activate E-stop to render the work-area safe. 
# Clean out remnants from the cutting area.
# Turn off power from the key switch, this will turn off the work-light.
# Deactivate/put away exhaust fan
# Power down voltage converter (green switch)
# Unplug circulation pump
# Turn off power to back of unit
# Lock the bay door by sliding the dead bolt closed and putting the brass padlock through the deadbolt


== Cut Guidelines ==  
== Cut Guidelines ==  
Line 179: Line 187:
# Select the part of your model to be exported to DXF (can select all)  
# Select the part of your model to be exported to DXF (can select all)  
# Use the plugin to create the DXF file, select mm as the export unit and export as lines
# Use the plugin to create the DXF file, select mm as the export unit and export as lines
# Transfer file to laser laptop
# Transfer file to laser workstation
# Open dxf in autocad save as 2004 dxf
# Open dxf in autocad save as 2004 dxf
# Follow the startup procedures as above
# Follow the startup procedures as above
# Follow the pre-cut procedures as above
# Test cut/engrave settings on a sample of the target work material (e.g. do Laser Coin Test)
# Test cut/engrave settings on a sample of the target work material (e.g. do Laser Coin Test)
# Import in lasercut5.1
# Import in lasercut5.1
Line 190: Line 199:
# Hit delete all
# Hit delete all
# Hit download current, this can take some time if the project is complex, if it takes too long you may want to break the cut up into smaller chunks.  
# Hit download current, this can take some time if the project is complex, if it takes too long you may want to break the cut up into smaller chunks.  
# Ensure the work area is clear of any obstructions
# Follow the pre-cut procedures as above
# Use test on the laser control panel to setup work piece
# Ensure the exhaust fan is on, connected and outside
# Ensure the circulating pump is on
# Ensure the lid is closed
# Hit start
# Hit start
 
# Follow the safe shutdown procedures as above




35

edits

Navigation menu