273
edits
3D printer, resin (ELEGOO Saturn) ID:170: Difference between revisions
Jump to navigation
Jump to search
3D printer, resin (ELEGOO Saturn) ID:170 (view source)
Revision as of 14:05, 5 March 2023
, 5 March 2023Update owner/status
Parker.link (talk | contribs) m (Add photo) |
(Update owner/status) Tags: Mobile edit Mobile web edit |
||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
| toolname = ELEGOO Saturn Resin 3D Printer | | toolname = ELEGOO Saturn Resin 3D Printer | ||
| model = ELEGOO Saturn | | model = ELEGOO Saturn | ||
| serial = | | serial = ?? | ||
| owner = | | owner = Brian Queen | ||
| loanstatus = | | loanstatus = Donated! | ||
| arrived = | | arrived = December 2022 | ||
| location = | | location = 3D Printer Village | ||
| status = Functional | | status = Functional | ||
| permission = None | | permission = None | ||
| Line 13: | Line 13: | ||
| caption = | | caption = | ||
| id = | | id = | ||
}} | }}https://www.elegoo.com/en-ca/products/elegoo-saturn-4k-mono-lcd-3d-printer | ||
==Specs== | ==Specs== | ||
*System: EL3D-3.0.1 | |||
*Operation: 3.5 Inch Touch Screen | |||
*Slicer Software: Chitu DLP Slicer | |||
*Connectivity: USB | |||
*Technology: LCD UV Photocuring | |||
*Lightsource: UV Integrated LED lights (wavelenth 405nm) | |||
*XY Resolution: 0.05mm(3840*2400) | |||
*Z Axis Accuracy: 0.00125mm | |||
*Layer Thickness: 0.01-0.15mm | |||
*Printing Speed: 30-40mm/h | |||
*Power Requirements: 110-240V 50/60Hz 24V4A 96W | |||
*Printer Dimensions: 11.02in (L) * 9.44in (W) * 17.55in (H) 28cm(L) *24cm (W) * 44.6cm (H) | |||
*Build Volume: 7.55in (L) * 4.72in (W) * 7.87in (H) 192mm (L) * 120mm(W) * 200mm (H) | |||
*Weight: 22 Lbs (10 Kg) | |||
==Usage== | ==Usage== | ||
The leveling card should be near the machine and contains basic build platform leveling instructions. | |||
I was told that ChiTu Box is bad at supports, and to do them in PrusaSlicer (you'll need to find/use/make a resin printer profile) then export your unsliced but supported model as STL for slicing in ChiTu Box. | |||
Below is the official usage guide, and you may want to [[3D printer, resin (Anycubic Photon 5.5) ID:159#Usage|refer to the similar usage steps for our other resin printer]], but can basically be summarized as: | |||
*BE CAREFUL not to damage the 4k LCD screen or FEP plastic film! | |||
*level the build platform | |||
*turn on / heat up cabinet, close doors! | |||
*fill tank with resin choice/color/amount | |||
*software, do your supports/slicing | |||
*cabinet warmed up now? | |||
*insert stick, hit go, leave for a while, check in occasionally for obvious fails | |||
*the build platform won't fit in the [[Curing station (Anycubic Wash and Cure Machine) ID:160]] | |||
*so remove your prints without damaging the build platform and toss them into the basket, see video ^ | |||
*pour unused resin back into bottle - the tank holding stand is good for this | |||
*clean out any remnants from the tank, being careful not to damage the FEP plastic film | |||
*CLEAN UP AFTER YOURSELF | |||
*Think you're done cleaning? THINK AGAIN!! | |||
[[File:Saturn1.JPG]] | |||
[[File:Saturn2.JPG]] | |||
[[File:Saturn3.JPG]] | |||
[[File:Saturn4.JPG]] | |||
[[File:Saturn5.JPG]] | |||
[[File:Saturn6.JPG]] | |||
[[File:Saturn7.JPG]] | |||
[[File:Saturn8.JPG]] | |||
[[File:Saturn9.JPG]] | |||
==Troubleshooting== | ==Troubleshooting== | ||
TBD | TBD | ||