Talk:Pinball machine (Williams Road Kings) ID:129: Difference between revisions

From Protospace Wiki
Jump to navigation Jump to search
m (Cjs moved page Talk:Pinball machine (Road Kings) to Talk:Pinball machine (Williams Road Kings): Updated to follow naming conventions.)
m (Cjs moved page Talk:Pinball machine (Williams Road Kings) to Talk:Pinball machine (Williams Road Kings) ID:129: Update name to follow naming conventions)
 

Latest revision as of 04:08, 31 January 2019

On talk pages, the newest sections are at the bottom of the page and the newest comments are at the bottom of each section. More on using talk pages

Maintenance Log

Log structure:

=== <trouble/repair topic> ===
Current status: <status> as of <date>

==== <log entry date> ====
<log entry content>
<status as of the end of the log entry>
<signature (type ~~~~ to insert your signature)>

==== <log entry date> ====
<log entry content>
…


=== <another trouble/repair topic> ===
Current status: <status> as of <date>
…

Flippers not working

Current status: Not working as of 2016-02-13

2016-02-06

Checked fuses—one had been replaced recently; it was still fine. The fuse on the "50 V FLIPPER POWER" board was blown. The fuse specification sticker was obscured by a warranty void sticker, so I checked the manual: 5 A slow-blow. We had no such fuses in stock. I tried a 5 A regular fuse and a 6 A regular fuse; both blew with a few flipper actuations.

Next I inspected the flipper mechanisms and found the right flipper's NC switch had blackened contacts and white residue on the leaves. It measured 400 ohms closed. John W. suggested that this might cause the machine to not detect that the flipper had returned to its rest position and continue applying power to the return coil of the solenoid. (Are the solenoids double-acting?) I tried sanding it in place, but this had no apparent effect, so I took it out and sandblasted it. It's perfectly clean and shiny now, with closed resistance under an ohm.

After cleaning the switch, I tried again with another 5 A regular speed fuse, which blew again after a few actuations of the flippers.

Not fixed yet—need to buy 5 A SB fuses.
–– Ian Oliver 01:46, 13 February 2016 (PST)


Left flipper sticks on the down-stroke

Current status: Not working as of 2016-02-13

2016-02-06

Detected during testing of flippers described above.

I first checked its motion by hand: the flipper moves up smoothly, but sticks (pretty hard) at two separate points when moving down, before reaching its rest position.

I then disassembled the flipper mechanism. All parts (flipper pivot, linkage, solenoid plunger) moved smoothly individually when disassembled. I reassembled it and it was no better than before.

I tried cleaning inside of solenoid with a paper towel patch and toothed tweezers, thinking there might be grit in it. Matt F. suggested that the solenoid may need lubrication; we didn't try that because we weren't sure what lubricant to use and the manual didn't say. (He thought looked like graphite, but we doubted this because it would be electrically conductive. Furthermore, it didn't wash off of my fingers easily.)

Not fixed yet—needs more diagnosis and/or proper lubrication
–– Ian Oliver 01:46, 13 February 2016 (PST)


Right coin acceptor not working

Current status: Partially working as of 2016-02-29

2016-02-23

Rutger did some work on the coin acceptor and it works now. The solenoid still buzzes sometimes, but this stops after you put in a coin. Coins seem to be correctly registered by the machine, but are not held for return reliably.

Partially fixed
–– Ian Oliver 17:59, 29 February 2016 (PST)