Laser cutter, large (Rabbit Laser RL-80-1290) ID:6

From Protospace Wiki
Jump to navigation Jump to search

← Back to tools we have

6.jpg
The large laser cutter, with its lid open and a piece of material on the bed
Type Laser Cutter
Make/Model Rabbit Laser USA RL-80-1290 (where RL is the factory code, 80 is the original laser power in watts, and 1290 represents the bed size (1200 x 900 mm))
Serial number ??
Original owner Brian Queen
Loan status Semi-Permanent Loan
Arrival date 2012-02
Location Bay 108, near the door to the front rooms
Functional status Working
Usage permissions Members & Friends Only
Certification Must complete Laser Certification
Wiki-ID 6
Label 1.0" 1.5" 2.0"


Arguably the most popular tool at Protospace, the laser cutter uses a CO2 laser to cut and engrave a variety of non-metal materials (though some metals can be engraved).

Software

We currently have LaserCut 6.0 installed on the computer connected to the Laser Cutter. Unfortunately LaserCut 6.0 requires a USB dongle to be hooked up to the PC at all times as a form of DRM. If you're running a personal copy you are restricted to a demo version (no saving - though there is a work around). Later versions (6.1+) have dropped the USB dongle requirement but can't communicate with our laser cutter directly.

Downloads

LaserCut 5.3 (Google Drive, Direct from Leetro) for Windows Paid, Demo

The full version, but requires a special SenseLock USB Dongle to be connected to the PC running it or the software is limited to a demo mode (which is still useful for familiarizing yourself with the program). This version is needed in order to communicate with our laser cutter, as 6.1 doesn't support ours.


LaserCut 6.1 (Google Drive, Direct from Leetro) for Windows Free

Not directly compatible with our laser cutter but has no USB dongle requirement, is fully functional aside from not being able to communicate with our laser cutter. Can still be used to prepare files for the earlier version of LaserCut (5.3). Both versions of LaserCut can be installed at the same time making this version a great option too.


123D Make (Direct from Autodesk) for Windows, Mac, iPad/iPhone Free

A program for converting 3D models into pieces which can be laser cut and attached together to form a fully 3D model out of laser cut materials (example).


Pepakura Designer (Direct from Tama Software) for Windows Paid, Demo

A program for converting 3D models into origami style pages which can be printed, cut out by hand and/or laser cut, then folded to form a 3D object (examples).

Resources

The Powerpoint presentation that is shown as part of the laser certification process, useful as a refresher once you've completed your certification.

TemplateMaker, a very useful Online tool for generating various custom boxes and shapes that can be cut on the laser.

Wolfie's SVG Puzzle Generator, exports a randomly generated puzzle in SVG format which can be converted to DXF and then laser cut out of something (in order to make personalized puzzles).

MakerCase, generates a proper box with the option to set the thickness of the material and pick which style of joints to use.


It is imperative that you do a chlorine test on unapproved materials before working on them with the laser cutter.

Specs

  • 80-watt DC-excited carbon dioxide laser tube
    • Water-cooled, with chiller accessible from the front
  • Bed size: 1200 mm × 900 mm (47.2" × 35.4")
    • Front panel of machine can be removed or folded down to insert pieces longer than 3' (though this can risk dangerous laser radiation exiting the machine, so be careful)
  • Controller: Leetro MPC 6525A
  • Can cut or etch up to 1/4" (6 mm)-thick light materials such as woods and some plastics in one pass, or thicker materials in multiple passes
  • Cut kerf is approximately 0.3 mm (full width); you should measure it with your material if it's important to your project
Do not cut any chlorinated synthetics (some types of plastics and rubbers)! The HCl vapors will damage the machine.

Usage Notes

Maintenance

Every Use

  1. Check water level in chiller
  2. Remove offcuts and scrap from the bottom

Monthly

  1. Clean inner and outer surfaces of laser cutter including window.
    • Use dilute Zep Fast 505 industrial degreaser or other cleaner on hard surfaces
    • Use windex on window
    • Avoid contaminating linear rails or optics
  2. Wipe linear rails clean with solvent degreaser. Do not move gantry or bearings onto cleaned section of rail until all solvent evaporated to prevent contamination of bearing grease
  3. Grease three linear bearings using grease located in the left side compartment
    • DO NOT USE ANY AEROSOL OR SPRAY LUBRICANT
    • TODO: fill in make/model/type of grease
  4. Remove and clean lens.
  5. Check condition of optics clean if necessary
  6. Check laser alignment. Adjust if necessary.
  7. Check bed level. Adjust if necessary.
  8. Check tension on all belts. Adjust if necessary.
  9. Check tension on all belts. Adjust if necessary.
  10. Inspect electronic components for operation including six limit switches (±X, ±Y, ±Z axis), lights and light wiring, electronics cooling fan
  11. Blow out dust from chiller radiator

As Required

  • Inspect Z-bed screws for smooth operation. Clean and regrease if required. Z screws must be thoroughly cleaned with solvent degreaser before re-applying clean grease.
  • Replace worn or failed laser optics including mirror or lens. Check alignment after any optics replacement.
  • Thoroughly clean smoke and residue off internal surfaces of laser cutter
    • Use concentrated Zep Fast 505 industrial degreaser
    • Avoid contaminating linear rails or optics

Repairs Needed

Replace shocks on lid

Bed is warped. X max side of the bed projects up.

History

  • 2012-02 - On loan for 6 months (ending 2012-08) in exchange for Protospace performing repairs
    • Loan has been extended
  • 2016-11-06: Chiller failure. Laser tube destroyed (overheated and glass cracked)
    • 2016-11-07: Laser tube replaced with an aging, but unused tube that was donated from a scrap laser
  • 2016-11-11: Chiller failure. Laser tube destroyed.
    • 2016-11-13: Two new laser tubes ordered from an American source.
    • 2016-11-24: Laser tube replaced, chiller pump is broken.
    • 2016-12-04: Chiller repaired. Alignment and power testing is pending.
    • 2016-12-18: Laser is fully operational.
  • 2019-08-17: Lens failure. [1]
    • 2019-08-17: New lens ordered.
    • 2019-08-21: Lens replaced, laser is working.
  • 2022-02-06
    • Tumblers from locks removed from front panel. They can now be turned by hand, making it easier to remove and replace the front panel during cleaning and servicing.