273
edits
3D printer, resin (ELEGOO Saturn) ID:170: Difference between revisions
3D printer, resin (ELEGOO Saturn) ID:170 (view source)
Revision as of 14:05, 5 March 2023
, 5 March 2023Update owner/status
(add specs) |
(Update owner/status) Tags: Mobile edit Mobile web edit |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
| model = ELEGOO Saturn | | model = ELEGOO Saturn | ||
| serial = ?? | | serial = ?? | ||
| owner = | | owner = Brian Queen | ||
| loanstatus = | | loanstatus = Donated! | ||
| arrived = | | arrived = December 2022 | ||
| location = 3D Printer Village | | location = 3D Printer Village | ||
| status = Functional | | status = Functional | ||
| Line 17: | Line 17: | ||
==Specs== | ==Specs== | ||
* System: EL3D-3.0.1 | *System: EL3D-3.0.1 | ||
* Operation: 3.5 Inch Touch Screen | *Operation: 3.5 Inch Touch Screen | ||
* Slicer Software: Chitu DLP Slicer | *Slicer Software: Chitu DLP Slicer | ||
* Connectivity: USB | *Connectivity: USB | ||
* Technology: LCD UV Photocuring | *Technology: LCD UV Photocuring | ||
* Lightsource: UV Integrated LED lights (wavelenth 405nm) | *Lightsource: UV Integrated LED lights (wavelenth 405nm) | ||
* XY Resolution: 0.05mm(3840*2400) | *XY Resolution: 0.05mm(3840*2400) | ||
* Z Axis Accuracy: 0.00125mm | *Z Axis Accuracy: 0.00125mm | ||
* Layer Thickness: 0.01-0.15mm | *Layer Thickness: 0.01-0.15mm | ||
* Printing Speed: 30-40mm/h | *Printing Speed: 30-40mm/h | ||
* Power Requirements: 110-240V 50/60Hz 24V4A 96W | *Power Requirements: 110-240V 50/60Hz 24V4A 96W | ||
* Printer Dimensions: 11.02in (L) * 9.44in (W) * 17.55in (H) 28cm(L) *24cm (W) * 44.6cm (H) | *Printer Dimensions: 11.02in (L) * 9.44in (W) * 17.55in (H) 28cm(L) *24cm (W) * 44.6cm (H) | ||
* Build Volume: 7.55in (L) * 4.72in (W) * 7.87in (H) 192mm (L) * 120mm(W) * 200mm (H) | *Build Volume: 7.55in (L) * 4.72in (W) * 7.87in (H) 192mm (L) * 120mm(W) * 200mm (H) | ||
* Weight: 22 Lbs (10 Kg) | *Weight: 22 Lbs (10 Kg) | ||
==Usage== | ==Usage== | ||
The leveling card should be near the machine and contains basic build platform leveling instructions. | |||
I was told that ChiTu Box is bad at supports, and to do them in PrusaSlicer (you'll need to find/use/make a resin printer profile) then export your unsliced but supported model as STL for slicing in ChiTu Box. | |||
Below is the official usage guide, and you may want to [[3D printer, resin (Anycubic Photon 5.5) ID:159#Usage|refer to the similar usage steps for our other resin printer]], but can basically be summarized as: | |||
*BE CAREFUL not to damage the 4k LCD screen or FEP plastic film! | |||
*level the build platform | |||
*turn on / heat up cabinet, close doors! | |||
*fill tank with resin choice/color/amount | |||
*software, do your supports/slicing | |||
*cabinet warmed up now? | |||
*insert stick, hit go, leave for a while, check in occasionally for obvious fails | |||
*the build platform won't fit in the [[Curing station (Anycubic Wash and Cure Machine) ID:160]] | |||
*so remove your prints without damaging the build platform and toss them into the basket, see video ^ | |||
*pour unused resin back into bottle - the tank holding stand is good for this | |||
*clean out any remnants from the tank, being careful not to damage the FEP plastic film | |||
*CLEAN UP AFTER YOURSELF | |||
*Think you're done cleaning? THINK AGAIN!! | |||
[[File:Saturn1.JPG]] | |||
[[File:Saturn2.JPG]] | |||
[[File:Saturn3.JPG]] | |||
[[File:Saturn4.JPG]] | |||
[[File:Saturn5.JPG]] | |||
[[File:Saturn6.JPG]] | |||
[[File:Saturn7.JPG]] | |||
[[File:Saturn8.JPG]] | |||
[[File:Saturn9.JPG]] | |||
==Troubleshooting== | ==Troubleshooting== | ||
TBD | TBD | ||