Milling machine, CNC (Tormach PCNC 1100) ID:49: Difference between revisions
Jump to navigation
Jump to search
(→Specifications: clean up) |
(→Documentation: removed USB glitch warning, as per SME that was a Mach3 quirk and no longer applicable to our PathPilot setup) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 21: | Line 21: | ||
==Specifications== | ==Specifications== | ||
* '''Table Size:''' 34" x 9.5" | *'''Table Size:''' 34" x 9.5" | ||
* '''Table Slots:''' | *'''Table Slots:''' | ||
** two drainage/alignment slots | **two drainage/alignment slots | ||
** three T-Slots 0.625" (5/8") | **three T-Slots 0.625" (5/8") | ||
** center slot -0.00 + 0.004" | **center slot -0.00 + 0.004" | ||
** outer slots 0.000 + 0.008" | **outer slots 0.000 + 0.008" | ||
* '''Travel / Work Envelope (X/Y/Z):''' 18" x 9.5" x 16.5" | *'''Travel / Work Envelope (X/Y/Z):''' 18" x 9.5" x 16.5" | ||
* '''Rapid traverse:''' X/Y at 90 IPM, Z at 65 IPM | *'''Rapid traverse:''' X/Y at 90 IPM, Z at 65 IPM | ||
* '''Maximum Workpiece Weight:''' 500 lbs. | *'''Maximum Workpiece Weight:''' 500 lbs. | ||
* '''Spindle Nose Diameter:''' 3 3/8" | *'''Spindle Nose Diameter:''' 3 3/8" | ||
* '''Spindle Taper:''' BT30 with spindle lock for easy single hand drawbar operation | *'''Spindle Taper:''' BT30 with spindle lock for easy single hand drawbar operation | ||
* '''Spindle Speed Range:''' 100 to 5140 RPM | *'''Spindle Speed Range:''' 100 to 5140 RPM | ||
* '''Spindle Motor:''' 1.5hp (2hp peak) induction motor | *'''Spindle Motor:''' 1.5hp (2hp peak) induction motor | ||
* '''Spindle Center to Column Face:''' 11" | *'''Spindle Center to Column Face:''' 11" | ||
* '''Maximum Spindle Nose to Table:''' 17" | *'''Maximum Spindle Nose to Table:''' 17" | ||
* '''Weight net / shipping:''' 1130 / 1325 lbs | *'''Weight net / shipping:''' 1130 / 1325 lbs | ||
* '''Operating temperature range:''' 7 to 38 '''°'''C | *'''Operating temperature range:''' 7 to 38 '''°'''C | ||
== Features == | ==Features== | ||
* NEMA 34 stepper motors on X, Y and Z | *NEMA 34 stepper motors on X, Y and Z | ||
* Single Shot Lube Pump | *Single Shot Lube Pump | ||
* 15 point lubrication. Each axis has an oil distribution channel milled full length on left and right vertical and horizontal surfaces (all 4 sliding surfaces) plus an oil line plumbed directly to the ball nut assembly | *15 point lubrication. Each axis has an oil distribution channel milled full length on left and right vertical and horizontal surfaces (all 4 sliding surfaces) plus an oil line plumbed directly to the ball nut assembly | ||
* Precision ground ball screws in the X, Y and Z motion. ISO/DIN P4 grade. | *Precision ground ball screws in the X, Y and Z motion. ISO/DIN P4 grade. | ||
* Complete way covers | *Complete way covers | ||
* Slide ways are a bonded low friction surface (PTFE filled acetyl), hand scraped slide ways with milled oil distribution slots. | *Slide ways are a bonded low friction surface (PTFE filled acetyl), hand scraped slide ways with milled oil distribution slots. | ||
* Forward opening electrical cabinet. This unique design allows service even when the machine is placed near to a wall. | *Forward opening electrical cabinet. This unique design allows service even when the machine is placed near to a wall. | ||
* Computer controlled spindle speed and direction with regenerative braking from 1.5 hp induction motor (2 hp peak) | *Computer controlled spindle speed and direction with regenerative braking from 1.5 hp induction motor (2 hp peak) | ||
* Cartridge style spindle with V-belt transmission. There are two overlapping speed ranges. Low belt speed is 100 – 2000 RPM, high belt is 250 – 5140 RPM | *Cartridge style spindle with V-belt transmission. There are two overlapping speed ranges. Low belt speed is 100 – 2000 RPM, high belt is 250 – 5140 RPM | ||
* Spindle safety is enhanced with a tool change safety interlock and key switch lockout. Main spindle contactor (VFD power) is automatically disengaged when operator is changing a tool. Spindle M-codes or manual spindle start will reengage VFD power automatically after tool change is completed. | *Spindle safety is enhanced with a tool change safety interlock and key switch lockout. Main spindle contactor (VFD power) is automatically disengaged when operator is changing a tool. Spindle M-codes or manual spindle start will reengage VFD power automatically after tool change is completed. | ||
* Operator console has manual override for all spindle controls. | *Operator console has manual override for all spindle controls. | ||
==Documentation== | ==Documentation== | ||
[https://tormach.com/support/mill/pcnc-1100-legacy-documents Tormach website] | [https://tormach.com/support/mill/pcnc-1100-legacy-documents Tormach website] | ||
[https://tormach.com/docs/download/assetlink/asset_id/584 Operator Manual | [https://tormach.com/docs/download/assetlink/asset_id/584 Operator Manual] | ||
[https://tormach.com/docs/download/assetlink/asset_id/205 Probe usage service bulletin] | [https://tormach.com/docs/download/assetlink/asset_id/205 Probe usage service bulletin] | ||
==Simulator== | ==Simulator== | ||
*Create an account at | *Create an account at https://www.tormach.com/pathpilot | ||
*Login to | *Login to https://hub.pathpilot.com/ | ||
*Choose our machine from older models at the bottom: | *Choose our machine from older models at the bottom: | ||
**Tormach PCNC 1100 | **Tormach PCNC 1100 | ||
Latest revision as of 17:09, 17 October 2022
 | |
| Type | CNC Mill (Tormach) |
| Make/Model | PCNC 1100 Personal CNC Mill Series 2 |
| Serial number | 231 11-2006 |
| Original owner | Protospace |
| Loan status | Bought for Protospace by a group of members |
| Arrival date | ? |
| Location | Metal shop |
| Functional status | Functional |
| Usage permissions | Members Only |
| Certification | Must complete Shop Safety, Lathe Training, 3D CAD Training, CAM Training, 1 on 1 Project |
| Wiki-ID | 49 |
| Label | 1.0" 1.5" 2.0" |
Specifications
- Table Size: 34" x 9.5"
- Table Slots:
- two drainage/alignment slots
- three T-Slots 0.625" (5/8")
- center slot -0.00 + 0.004"
- outer slots 0.000 + 0.008"
- Travel / Work Envelope (X/Y/Z): 18" x 9.5" x 16.5"
- Rapid traverse: X/Y at 90 IPM, Z at 65 IPM
- Maximum Workpiece Weight: 500 lbs.
- Spindle Nose Diameter: 3 3/8"
- Spindle Taper: BT30 with spindle lock for easy single hand drawbar operation
- Spindle Speed Range: 100 to 5140 RPM
- Spindle Motor: 1.5hp (2hp peak) induction motor
- Spindle Center to Column Face: 11"
- Maximum Spindle Nose to Table: 17"
- Weight net / shipping: 1130 / 1325 lbs
- Operating temperature range: 7 to 38 °C
Features
- NEMA 34 stepper motors on X, Y and Z
- Single Shot Lube Pump
- 15 point lubrication. Each axis has an oil distribution channel milled full length on left and right vertical and horizontal surfaces (all 4 sliding surfaces) plus an oil line plumbed directly to the ball nut assembly
- Precision ground ball screws in the X, Y and Z motion. ISO/DIN P4 grade.
- Complete way covers
- Slide ways are a bonded low friction surface (PTFE filled acetyl), hand scraped slide ways with milled oil distribution slots.
- Forward opening electrical cabinet. This unique design allows service even when the machine is placed near to a wall.
- Computer controlled spindle speed and direction with regenerative braking from 1.5 hp induction motor (2 hp peak)
- Cartridge style spindle with V-belt transmission. There are two overlapping speed ranges. Low belt speed is 100 – 2000 RPM, high belt is 250 – 5140 RPM
- Spindle safety is enhanced with a tool change safety interlock and key switch lockout. Main spindle contactor (VFD power) is automatically disengaged when operator is changing a tool. Spindle M-codes or manual spindle start will reengage VFD power automatically after tool change is completed.
- Operator console has manual override for all spindle controls.
Documentation
Simulator
- Create an account at https://www.tormach.com/pathpilot
- Login to https://hub.pathpilot.com/
- Choose our machine from older models at the bottom:
- Tormach PCNC 1100
- Serial Number 231
- Built in 11-2006
- Base model, no upgrades
- PathPilot CNC 2
References: forum and mailing list