View source for Lathe, metal (Challenger 1660G) ID:46

{{Equipment page
| toolname = Metal lathe
| model = Challenger 1660G (aka Birmingham LUX 1660G or YCL-1660)
| serial = ??
| owner = Protospace
| loanstatus = Owned by Protospace
| arrived = 2015-12-22
| location = Metal shop
| status = Working
| permission = Open to full members
| certification = [https://my.protospace.ca/courses/281 Metal Cutting & Manual Lathe]
| id = 46
| itemphoto = [[File:46.jpg|350px|thumb|right|]]
}}

[[Category:Metalworking tools]]
[[Category:Machine tools]]
[[Category:Showcase tools]]

==Specifications==
All from the 1640T/1660T page listed in the Documents section unless noted.

*Dimensions: 29" deep × 72" long × ?? tall (according to John W)
*Mass: ~4000–5000 lbs
*Motor: 7.5 hp, 3-phase, 220 V
*36–1800 RPM spindle speed in 12 steps
*Capacities
**Swing over bed: 16"
**Swing over cross slide: 10"
**Distance between centers: 60"
**Swing in gap: 60"
**Width of bed: 24"
*Headstock
**Spindle nose: ASA D1-6
**Spindle bore: 2 1/16" or 2 1/8"
**Spindle taper: MT 6
**Spindle speeds: 36, 60, 82, 93, 158, 215, 302, 510, 695, 786, 1328, 1800 rpm
*Threads & feeds
**Imperial threading: 2–72 TPI (45 kinds)
**Metric threading: 0.2–14mm (40 kinds)
**Module pitch threading: 0.3–3.5 M.P. (18 kinds) (for making shafts for worm gears)
**DP threading: 8–44 DP (21 kinds)
**Longitudinal feed range: 0.002"–0.04" ipr
**Cross feed range: 0.001"–0.02" ipr
*Carriage
**Cross slide travel: 8 1/4"
**Compound slide travel: 5 1/4"
*Tailstock
**Center taper: MT 4
**Quill travel: 6 1/4"
**Quill diameter: 2 1/16"
*Coolant pump
*Safety foot brake

<br />

==Jank==

===Carriage Lock===
If the carriage doesn't freely/easily move in the X direction, there's a fat hex bolt head sticking up on the right side of it that needs loosening.

(add pic here)

===Power Feed===
Note that while <u>generally gears/speeds shouldn't be changed while the lathe is in motion</u>, from https://forum.protospace.ca/t/can-t-get-lathe-power-feed-to-work/3568/8<blockquote>Set it to a lowish speed like 400 or less and bump the jog button. Then start wiggling leavers while it’s coasting down and watch the drive shaft and screw. You’ll feel it when it engages and the shafts will start spinning…

The threading lead screw and the power feed drive shaft are taken off at different points in the gear train. It is possible to jiggle a leaver and get one to start spinning while the other is still not engaged properly and requires further jiggling.

The XYWZ lever is the worst and usually requires persuasion to engage. The gears are all straight cut, and all may require sufficient wigglage before they cooperate. And the number dial is keep turning until it works. It’s about 1/4 past the number you want.</blockquote>[[File:20180206_230213_720p.mp4|frameless]]
<br />

==Documents==

=== Reference ===

*[http://www.southern-tool.com/store/birmingham_lux-1640-g_lathes.php Sales page for 1640T and 1660T models]
*According to those in the know (Danny P and John W) there are three manuals for this machine:
*[https://wiki.protospace.ca/images/c/c2/Lux_Matter_Metal_Lathe_Manual_1660G.pdf 1640G/1660G Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/2/2c/Lux-Matter_1660T_Manual_from_Luc_Archer.pdf 1640T/1660T Instruction Manual and Parts List]
*[https://wiki.protospace.ca/images/5/5e/LUX-Matter_1600_Series_Instruction_Manual.pdf 1500/1600 Instruction Manual and Parts List]

=== Training ===
(training material linked here?)

=== Practical Project ===
(tired of digging this out of drive, insert here?)<br />
==Tooling==
{| class="wikitable mw-collapsible mw-collapsed"
|+

!Short Description
!Shank Size
!Typical Insert Types
!Long Description
!Photo
!Manuf Code
!ANSI
!ISO
!Replacement Screw Type
!Manufacturer
!New Price
!Condition
!Notes
|-
|Grooving Insert Holder
|3/8 "
|GIE-7
|Right Hand, 4.5" long, grooving, parting and turning tool
|[[File:THE-7-3 8-R.jpg|150px]]
|THE-7-3/8-R
|
|
|
|Nicole
|$110.7
|Good
|
|-
|Boring Bar
|3/4 "
|CCMT33x, CCxT33x
|Boring bar, RH, 7" (174 mm) long
|[[File:BoringBar174 small.jpg|150px]]
|
|
|
|
|
|
|Poor
|Damage reduces insert support.  Missing insert screw.
|-
|Boring Bar
|3/4 "
|CCMT33x, CCxT33x
|Boring bar, RH, 5 3/4" (144 mm) long
|[[File:BoringBar144 small.jpg|150px]]
|
|
|
|
|
|
|Poor
|Damage reduces insert support. Missing insert screw.
|-
|Boring Bar
|3/4 "
|CCMT33x, CCxT33x
|Boring bar, RH, 4 7/8" (121 mm) long
|[[File:BoringBar121.jpg|150px]]
|
|
|
|
|
|
|Serviceable
|Missing insert screw.
|-
|Boring Bar
|1"
|CCMT33x, CCxT33x
|Boring bar, RH, 8" long
|[[File:SER 1000 M16.jpg|150px]]
|
|
|
|
|
|
|Fair
|Missing insert screw.
|-
|Threading Insert Holder
|1"
|Full form or partial form.  See notes.
|Threading insert holder
|[[File:IscarThreadingInsertHolder.jpg|150px]]
|SER 1000 M16
|
|
|
|Iscar
|US$158.62
|Fair
|Scuffing.  See manufactures documentation for insert selection.
Image shows regular turning insert, not threading insert.
|-
|Triangular RH, G Insert Holder
|3/4"
|TNMG43x, TNxG43x
|Triangular RH, ANSI G Type
|[[File:MTJNRS 46- 4 D.jpg|150px]]
|
|MTJNRS 46- 4 D
|
|
|Valenite
|
|Serviceable
|ANSI shank numbers are flipped.  Damaged shank.  Shank has been machined.
|-
|Triangular RH, J Insert Holder
|3/8"
|TNMG32x, TNxG32x
|Triangular RH, ANSI J Type
|[[File:TBR12_3_8_IC.jpg|150px]]
|
|TBR12 3/8 I.C.
|
|
|Carboloy
|
|Fair
|
|-
|Parting Tool Holder
|3/4"
|HSS
|HSS parting tool holder.  Quick change for 3/4" tool post.
|[[File:PartingToolHolder_small.jpg|150px]]
|
|
|
|
|
|
|Good
|
|}

==History==
This lathe was bought by Protospace using funding approved for the purchase of new machine tools at the December 2015 members' meeting. It was picked up and brought to Protospace on 2015-12-22 along with [[milling machine (ACRA AM4V)|the ACRA mill]] and [[air compressor, 80-gallon (MAXair Premium)|the new 80-gallon air compressor]]. It replaces [[lathe, metal (Torrent)|Kyle Paavola's lathe]]; it has equivalent capability. It came with the following accessories:

*3-jaw chuck
*4-jaw chuck
*Big steady rest
*Taper attachment
*40-position tool post and one tool holder with a carbide tool holder in it
*Live center
*A carriage stop with a micrometer
*Coolant pump