Laser cutter, large (Rabbit Laser RL-80-1290) ID:6: Difference between revisions
Jump to navigation
Jump to search
(Updated model link to Rabbit Laser's new specifications page (closest model).) |
m (Added "The Laser Cutter" Video.) |
||
| Line 1: | Line 1: | ||
{{#evt: | |||
service=youtube | |||
|id=https://www.youtube.com/watch?v=29YLiiapFHc | |||
|alignment=right | |||
}} | |||
{{Template:EquipmentPage | {{Template:EquipmentPage | ||
|toolname=Laser Cutter | |toolname=Laser Cutter | ||
| Line 10: | Line 16: | ||
|permission=Members & Friends Only | |permission=Members & Friends Only | ||
|certification=Must complete [[Laser Certification]] | |certification=Must complete [[Laser Certification]] | ||
|itemphoto= | |itemphoto=[[File:Laser cutter, open.jpg|350px|thumb|right|]] | ||
}} | }} | ||
| Line 18: | Line 24: | ||
[[Category:Textileworking tools]] | [[Category:Textileworking tools]] | ||
[[Category:Computer-controlled tools]] | [[Category:Computer-controlled tools]] | ||
==Specs== | ==Specs== | ||
| Line 32: | Line 39: | ||
* Perform a simple [[Chlorine Test]] on unapproved materials, as cutting or etching chlorinated materials damages the optics | * Perform a simple [[Chlorine Test]] on unapproved materials, as cutting or etching chlorinated materials damages the optics | ||
* See [[Power Levels]] page for notes and details on cutting and etching various materials | * See [[Power Levels]] page for notes and details on cutting and etching various materials | ||
* Power modulation | * Power modulation is in a restricted range in the software due to a firmware bug (Approximately 8%-30% represents 0%-100% power) | ||
* Controller occasionally locks up after large cut jobs. E-stop immediately if job timer does not increment in first 5 seconds of job. Post to list for recovery instructions | * Controller occasionally locks up after large cut jobs. E-stop immediately if job timer does not increment in first 5 seconds of job. Post to list for recovery instructions | ||
* Consult our [[Laser Standard Operating Procedure]] | * Consult our [[Laser Standard Operating Procedure]] | ||
Revision as of 06:44, 22 November 2015
| [[File:{{{id}}}.jpg|250px]] | |
| Type | Laser Cutter |
| Make/Model | RL1290 |
| Serial number | ?? |
| Original owner | Brian Queen |
| Loan status | Semi-Permanent Loan |
| Arrival date | Before 2013 |
| Location | Main Bay |
| Functional status | Functional |
| Usage permissions | Members & Friends Only |
| Certification | Must complete Laser Certification |
| Wiki-ID | [[{{{id}}}]] |
| Label | 1.0" 1.5" 2.0" |
Specs
- 80 watt
- 4x3' CNC bed
- Front shield can be dropped to insert pieces longer than 3'
- Water cooled & Ducted
- Can cut or etch up to 1/2" thick light materials such as woods and some plastics
- Cannot cut any chlorinated synthetics (some types of plastics & rubbers)
Usage Notes
- Complete Laser Certification to learn how to use the laser. Training is offered about once a month.
- Perform a simple Chlorine Test on unapproved materials, as cutting or etching chlorinated materials damages the optics
- See Power Levels page for notes and details on cutting and etching various materials
- Power modulation is in a restricted range in the software due to a firmware bug (Approximately 8%-30% represents 0%-100% power)
- Controller occasionally locks up after large cut jobs. E-stop immediately if job timer does not increment in first 5 seconds of job. Post to list for recovery instructions
- Consult our Laser Standard Operating Procedure
History
- Originally on loan for 6 months (ending Aug 2012) in exchange for Protospace performing repairs.
- Loan has been extended.
Repairs Needed
- Upgrades discussed
- Adding air cooling to optics and laser head block
- Convincing power supply to modulate power levels properly
- Seal display on controller to prevent smoke from clouding over time.