Embroidery machine, CNC (Tajima TEJT II-C NEO 1501) ID:144: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
(Added Troubleshooting & First link) |
||
Line 30: | Line 30: | ||
*Weight 40 thread | *Weight 40 thread | ||
=== '''Needle Replacement Procedure''' === | ==='''Needle Replacement Procedure'''=== | ||
# Loosen Flathead screw, remove worn or damaged needle | #Loosen Flathead screw, remove worn or damaged needle | ||
# When installing needle, vertical groove faces user, seat needle fully into holder. | #When installing needle, vertical groove faces user, seat needle fully into holder. | ||
# Ensure vertical groove still aligned before tightening | #Ensure vertical groove still aligned before tightening | ||
# Tighten flathead screw | #Tighten flathead screw | ||
# Rethread the needle | #Rethread the needle | ||
=== Changing a Spool === | ===Changing a Spool=== | ||
# Load on new spool | #Load on new spool | ||
# Cut old spool. | #Cut old spool. | ||
# Tie end of old thread to new thread. Clip any extra and stray material so it does not get caught when you pull it through | #Tie end of old thread to new thread. Clip any extra and stray material so it does not get caught when you pull it through | ||
# Pull the old thread from the needle side. The new thread will get pulled through the tubing and tensioners automagically | #Pull the old thread from the needle side. The new thread will get pulled through the tubing and tensioners automagically | ||
# Cut new thread and rethread the needle | #Cut new thread and rethread the needle | ||
=== Rethreading A needle === | ===Rethreading A needle=== | ||
To cleaning cut a thread, put new thread under NO TENSION and cut at an angle. This makes the thread end a wedge and un-frayed which is far easier to thread through the eye of a needle | To cleaning cut a thread, put new thread under NO TENSION and cut at an angle. This makes the thread end a wedge and un-frayed which is far easier to thread through the eye of a needle | ||
Thread needle front to back (away from user), raise thread end up and into spring to hold it there. | Thread needle front to back (away from user), raise thread end up and into spring to hold it there. | ||
'''Troubleshooting''' | |||
[https://forum.protospace.ca/t/troubleshooting-the-embroidery-machine-tip/2418 Machine detected a thread breakage] |
Revision as of 03:38, 22 August 2022
Type | CNC embroidery machine |
Make/Model | Tajima TEJT II-C NEO 1501 |
Serial number | 3127 |
Original owner | Protospace |
Loan status | N/A |
Arrival date | Feb 9th, 2021 |
Location | Sewing Room |
Functional status | Waiting for training material |
Usage permissions | ?? |
Certification | Course |
Wiki-ID | 144 |
Label | 1.0" 1.5" 2.0" |
Documentation
Specs
- Single-head 15-needle
- arm-style
- 19.5” L x 14” D; 32” door clearance
- up to 1,200 stitches per minute
- 170 lb. welded frame
- Cost: $8500.00
- Weight 40 thread
Needle Replacement Procedure
- Loosen Flathead screw, remove worn or damaged needle
- When installing needle, vertical groove faces user, seat needle fully into holder.
- Ensure vertical groove still aligned before tightening
- Tighten flathead screw
- Rethread the needle
Changing a Spool
- Load on new spool
- Cut old spool.
- Tie end of old thread to new thread. Clip any extra and stray material so it does not get caught when you pull it through
- Pull the old thread from the needle side. The new thread will get pulled through the tubing and tensioners automagically
- Cut new thread and rethread the needle
Rethreading A needle
To cleaning cut a thread, put new thread under NO TENSION and cut at an angle. This makes the thread end a wedge and un-frayed which is far easier to thread through the eye of a needle
Thread needle front to back (away from user), raise thread end up and into spring to hold it there.
Troubleshooting