Bandsaw, metal, horizontal (Craftex B013N): Difference between revisions

From Protospace Wiki
Jump to navigation Jump to search
No edit summary
(Seeded page)
Line 1: Line 1:
{{Template:EquipmentPage
{{Template:EquipmentPage
|toolname=Band Saw (Horizontal)
|toolname=Horizontal Metalcutting Bandsaw
|model=Crafted B013N
|model=Craftex B013N
|serial=??
|serial=??
|owner=Jim Akeson
|owner=Jim Akeson
|loanstatus=Loan to Space
|loanstatus=On Loan
|arrived=Dec 2012
|arrived=18Dec2012
|location=Metalworking Shop
|location=Metalworking Shop/Welding
|status=Working
|status=Working
|permission=Open to Members & Friends
|permission=Open to Members, must fix/replace if you break it
|certification=??
|certification=Demo/Read Notes
|itemphoto=[[File:BandSawHorizontal.jpg|350px|thumb|right|]]
|itemphoto=[[File:Bandsaw_Horizontal.jpg|350px|thumb|right|]]
}}
}}


==Notes==
[[File:Bandsaw_Horizontal_2.jpg|350px|thumb|right|]]


* You Break it, You Fix it
==Specs==


==Specs==
* Capacity: At 90 degree 4" x 6" rectangular 4 1/2" round
Capacity: At 90 degree 4" x 6" rectangular 4 1/2" round
* Speed: 80,120,200 FPM
* Gearbox: Sealed worm gear
* Motor: 1/3 HP, 110V, 1 phase belt drive, sealed worm gear transmission
* Table: 8" x 8 3/4" for vertical use
* Ball bearing drive wheels and blade guides
* Auto shut off
* Blade size 1/2" x .025" x 64 1/2"
* Gross weight: 50kg.
* Carton size: 15" x 13" x 41 1/2"


Speed: 80,120,200 FPM
==Usage Notes==


Gearbox: Sealed worm gear
* Can be used as both gravity-fed bandsaw or as an upright
 
* If used as upright, can attach cutting deck, 2 Phillips screws
Motor: 1/3 HP, 110V, 1 phase belt drive, sealed worm gear transmission
* Do not apply pressure when cutting flat, gravity is proper cutting weight
 
* 3-stepped pulleys to vary speed/torque
Table: 8" x 8 3/4" for vertical use
* Check blade tension before each use and that blade is seated in contact with bearings properly, that bearings are clean
 
* If blade comes off, power down and unplug, unscrew door knob, slide bottom plate on door up or it will snap off. Loosen tension via top knob, place blade back onto wheel grooves, re-tighten, close door and replace knob.
Ball bearing drive wheels and blade guides
* Sweep or blow debris off after each use
 
Auto shut off
 
Blade size 1/2" x .025" x 64 1/2"
 
Gross weight: 50kg.
 
Carton size: 15" x 13" x 41 1/2"

Revision as of 14:56, 19 December 2012

← Back to tools we have

[[File:{{{id}}}.jpg|250px]]
Type Horizontal Metalcutting Bandsaw
Make/Model Craftex B013N
Serial number ??
Original owner Jim Akeson
Loan status On Loan
Arrival date 18Dec2012
Location Metalworking Shop/Welding
Functional status Working
Usage permissions Open to Members, must fix/replace if you break it
Certification Demo/Read Notes
Wiki-ID [[{{{id}}}]]
Label 1.0" 1.5" 2.0"


Bandsaw Horizontal 2.jpg

Specs

  • Capacity: At 90 degree 4" x 6" rectangular 4 1/2" round
  • Speed: 80,120,200 FPM
  • Gearbox: Sealed worm gear
  • Motor: 1/3 HP, 110V, 1 phase belt drive, sealed worm gear transmission
  • Table: 8" x 8 3/4" for vertical use
  • Ball bearing drive wheels and blade guides
  • Auto shut off
  • Blade size 1/2" x .025" x 64 1/2"
  • Gross weight: 50kg.
  • Carton size: 15" x 13" x 41 1/2"

Usage Notes

  • Can be used as both gravity-fed bandsaw or as an upright
  • If used as upright, can attach cutting deck, 2 Phillips screws
  • Do not apply pressure when cutting flat, gravity is proper cutting weight
  • 3-stepped pulleys to vary speed/torque
  • Check blade tension before each use and that blade is seated in contact with bearings properly, that bearings are clean
  • If blade comes off, power down and unplug, unscrew door knob, slide bottom plate on door up or it will snap off. Loosen tension via top knob, place blade back onto wheel grooves, re-tighten, close door and replace knob.
  • Sweep or blow debris off after each use
Retrieved from "https://wiki.protospace.ca/index.php?title=Bandsaw,_metal,_horizontal_(Craftex_B013N)&oldid=900"